Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 122

Страница: 122 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 122 of 128

DANGER!

Risk of injury due to cutting and amputation!

Cuts and amputations can occur on:



Sharp edges of the conductor rails.



Cut edges when trimming rails.

→

Wear personal protective equipment!

→

Cordon off the work area!

→

Use caution when working in the vicinity, particularly below the conductor rail

DANGER!

Risk of injury due to crushing skin and limbs!

There is a risk of crushing of skin and limbs due to:



Spring force/gravity (stored energy).



Current collector (spring force) during installation, disassembly and maintenance.



Falling parts of the conductor rail system in the case of improper disassembly.



Moving parts when the system is in operation.

→

Do not enter the danger zones of the system during operation.

→

When working on the conductor rail system, wear protective footwear, protective gloves

and protective headgear.

DANGER!

Risk of death due to electrical shock!

Contact with components carrying electrical power can lead to death due to electrical shock

or severe injury. Risk of injury due to shock reactions, falling or being thrown across the

room due to electrical shock.

→

The main power supply (from the building) must be disconnected in the disassembly area

and secured against switching on again.

→

Disconnect all voltage supply line feeds.

→

When decommissioning, check whether a voltage is still present in the components and

take measures where necessary.

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды