Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 94

Страница: 94 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 94 of 128

WARNING!

Risk of wear and damage!

The distance from the securing base surface of the current collector to the running surface of the con-

ductor rail is an important functional dimension. This dimension changes in curves if the current col-

lector is not installed directly under the wheel contact point of the EMS hanger. If the distance from

the wheel contact point is too great, the permissible tolerances may be exceeded in tighter curves.

Result: Damage, high wear

→

Compliance with the installation tolerances must therefore be checked in the tightest curved section!

Fig. 130: Protect unoccupied current collector connecting cable with the protective cap provided (08150A / B…; 08150x…)

NOTE!

The protective cap is supplied pre-installed on the current collector. A replacement protective

cap can be ordered as a packing unit with Order No.: 08-A025-0080!
Install all current collector cables with high flexibility and without tensile or directional forces!

Fig. 131: Comparison of the correct and incorrect position of the socket sleeve

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды