manualshive.com logo in svg

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Поделиться
Скачать
Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 8

Operating Instructions 

 

Single-pole Conductor Rail System 

SingleFlexLine Program 0815 

 

 

BAL0815-0002g-US 
www.conductix.us 

translated document 

page 8 of 128 

2.2

 

Personnel requirements 

2.2.1

 

Qualifications 

 

WARNING! 

Inadequately trained persons are at risk of injury! 

Unintended use can result in serious injury to persons and property. 

→

 

All activities must only be performed by qualified personnel. 

 

 

Only persons who can be expected to perform their work reliably are acceptable personnel. People whose reactions are impaired 
by drugs, alcohol or medications, for example, are not authorized. 

 

When selecting personnel, all age- and occupation-specific guidelines applicable at the place of use must be observed. 

 
The following qualifications are specified in the operating instructions for certain fields of activity. 
 

 

Specialist personnel 

Consists of persons capable of performing assigned tasks and independently identifying and avoiding potential hazards based 
on their specialist training, knowledge and experience as well as their understanding of the applicable regulations. 
Personnel are considered qualified if they have successfully concluded training, for example, as electricians, master electricians, 
electrical engineers or electrical technicians. Personnel are also considered qualified who have been employed correspondingly 
for several years, have been educated in theory and practice during that time and whose knowledge and skills in the trade 
required have been tested. 
The operator of the machine or system must document that the corresponding certification, or other documentation of qualifica-
tion, is available or had been submitted previously. 
The installation, maintenance and commissioning of electrical equipment may only be conducted by qualified personnel (electri-
cians) according to local regulations. Work with higher installation positions typically requires additional qualifications and certif-
icates for the use of lifting devices and protective equipment. On the part the manufacturer, professional and proper handling of 
components is required. It is recommended that the installation personnel be trained by the manufacturer or that accompaniment 
of the installation by specialist fitters/supervisors be scheduled. 

 

Operators 

Have been instructed in a training session by the operator with respect to the tasks assigned to them and the potential dangers 
arising from improper actions. 
The operator of the machine or facility must document that the corresponding training has taken place. 

 

Transport personnel 

Trained persons with appropriate training in transporting goods safely, who transport the material indoors and outdoors accord-
ing to safety regulations. 

 

 

Содержание SingleFlexLine Program 0815

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды