Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 54

Страница: 54 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 54 of 128

After mounting the connector cap, check the connection for solidity by gently pulling.
If the conductor rails can be pulled apart, the connector clamp is most likely incorrectly mounted (see

Fig. 49).

→

Attach the connector cap centrally from behind and clip it into the insulating profile.

→

Engage the conductor rails in the hanger clamps (see Fig. 52).

Fig. 52: Support profile with a conductor rail installed

CAUTION!

Conductor rails can become deformed when bent!

→

Check conductor rail bends for the correct profile since conductor rails can deform when bent in

the area of the insulation.

→

Push a current collector through the conductor rail by hand. The current collector must slide

through the conductor rail bend without jamming.

→

For a PE

plus

rail, use a PE

plus

current collector with a broader brush

→

If the connector cap cannot rest on the guideway profile, hanger clamps must be placed at maximum distances of 200 mm on

both sides of the connector position (see Fig. 53).

Fig. 53: Rail connector

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды