manualshive.com logo in svg

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Поделиться
Скачать
Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 19

Operating Instructions 

 

Single-pole Conductor Rail System 

SingleFlexLine Program 0815 

 

 

BAL0815-0002g-US 
www.conductix.us 

translated document 

page 19 of 128 

3.2.1

 

Lengths 

Max. length of the installed conductor rail 

Any, depending on the line feed design 

Conductor bars 

Max. 4000 mm (standard), 6000 mm and short lengths on request 

Min. permissible conductor bar length 

300 mm 

Supplementary length per connection point  

10 mm 

3.2.2

 

Installation orientation 

 

WARNING! 

Danger due to increased wear or damage!

 

→

 

Install the current collector with its central axis exactly on the central axis of the conductor rail. 

→

 

The mean distance between the outrigger axis and the contact surface must be precisely complied 

with. 

 

 

WARNING! 

Loss of contact or increased heating!

 

Risk of injury due to loss of contact or increased heating if the current collector is operated outside the 
permissible installation position. 

3.2.3

 

Tolerances 

The conductor rail must be installed within the following tolerances. Conductix-Wampfler does not accept any responsibility for the 
conductor rail's correct functioning if these tolerances are not observed. In such a case, Conductix-Wampfler does not accept any 
liability for problems that arise if the conductor rail system is not functioning correctly. 
 

Conductor rails 

X: ±3 mm; Y: ±1 mm (see Fig. 1) 

Current collector* 

X: ±10 mm; Y: ±10 mm (X: ± 15 mm, Y: ± 15 mm) 

Force with which the current collector contacts the rail 

Approx. 9 N 

*depending on the current collector type 
 

 

Fig. 1: Conductor bar 0815 coordinate system 

Y

X

Z

Y

X

Z

Содержание SingleFlexLine Program 0815

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды