manualshive.com logo in svg

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Поделиться
Скачать
Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 17

Operating Instructions 

 

Single-pole Conductor Rail System 

SingleFlexLine Program 0815 

 

 

BAL0815-0002g-US 
www.conductix.us 

translated document 

page 17 of 128 

 

DANGER! 

Risk of injury due to energy storage! 

If consumers with energy storage are supplied by the conductor rail, these must be disconnected 
from the conductor rail or the energy storage system must be discharged according to the manu-
facturer’s specifications before starting work and system checked for the absence of a voltage. 

2.9

 

Conduct in the event of accidents and malfunctions 

Measures to take in the event of accidents: 

 

Shut down the system and secure it against unauthorized, unintentional and/or erroneous activation. 

 

Secure the danger zone. 

 

Remove persons from the danger zone. 

 

Initiate first aid measures. 

 

Alert the rescue services. 

 

Inform responsible parties at the operating site. 

 

Make access available for rescue vehicles. 

 

Measures to take in the event of malfunctions: 

 

Shut down the system and secure it against unauthorized, unintentional, and/or erroneous reactivation.

 

 

Secure the work area against entry.

 

 

Consult qualified personnel when analyzing the fault.

 

 

Check for disconnection from power.

 

 

Remove the product and replace it with a new product.

 

 

Determine the cause of error and repair the product.

 

 

Содержание SingleFlexLine Program 0815

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды