Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 124

Страница: 124 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 124 of 128

11.2

Disassembly

After the system is no longer in use, the device must be disassembled and environmentally friendly disposal carried out.

Before starting disassembly:

DANGER!

Risk of injury due to impacts and punctures/stabs from conductor rails sliding out!

Risk of injury due to impacts and punctures/stabs from conductor rails sliding out when the packag-

ing units are held at an angle, the packaging is damaged or through carelessness with long

loads/transport crates.

→

Wear personal protective equipment!

→

Cordon off the work area!

→

Remove operating and auxiliary materials as well as residual processing material and dispose of them in an environmentally

appropriate manner.

WARNING!

Be aware of dangers due to electric shock, harmful dusts, sharp edges and moving parts!

→

Clean the subassemblies and components properly and disassemble them under observation of applicable local occupational

safety and environmental protection regulations.

11.2.1

Disassemble the conductor rails

WARNING!

Risk of injury due to improper disassembly!

Stored residual energy, sharp components, sharp points and edges on and in the device or the re-

quired tools can cause injury.

→

Ensure that there is sufficient space before starting work.

→

Handle open, sharp-edged components carefully.

→

Ensure that the workplace is tidy and clean!

→

Disassemble components properly.

→

Consult the manufacturer in case of doubt.

Personnel



May only be carried out by trained technicians



At least two people

Required tools



Disassembly tool (see Section 6.3.3.3 and page 55)



Hexagonal screwdriver

SW 2.5



Hexagonal screwdriver

SW 3



Open-end wrench

SW 7



Flat-head screwdriver

1.2 x 6.5x150 mm



Cutting tool (e.g., jigsaw)



Tools for securing

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды