Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 35

Страница: 35 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 35 of 128

DANGER!

Risk of injury due to crushing skin and limbs!

There is a risk of crushing of skin and limbs due to:



Spring force/gravity (stored energy).



Current collector (spring force) during installation, disassembly and maintenance.



Be aware of the risk of falling conductor rail system components if they have not been
properly installed or if operated in inappropriate operating conditions (e.g., environment that
contains solvents).

→

Only allow installation to be conducted by specialized technicians.

→

When working on the conductor rail system, wear protective footwear, protective gloves,

and protective headgear.

→

When changing the sliding contacts, follow the separate instructions for this task. See Sec-

tion 12.1.

→

Only install the conductor rail system where suitable operating conditions prevail. See Sec-

tion 3.3.

DANGER!

Risk of injury due to ensnarement or impact!

Ensnarement and/or impact with moving conductor rails (slip ring) or current collectors con-

nected to the machine and other components must be prevented.

→

Cordon off the work area.

→

Use caution when working in the vicinity of the danger zone, particularly if protective de-

vices (covers, enclosures, control devices) have been removed or disabled.

→

Use caution when working in the vicinity of the danger zone, particularly below the con-

ductor rail.

→

Be aware of the risk of falling conductor rail system components if they have not been

properly installed or if operated in inappropriate operating conditions (e.g., environment

that contains solvents).

→

Wear personal protective equipment!

DANGER!

Risk of injury due to cutting and amputation!

Cuts and amputations can occur:



On sharp edges of the general components.



On sharp edges of the conductor rails.



On cut edges when trimming the conductor rails.



On packaging materials (cartons, bands, etc.)

→

Wear personal protective equipment!

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды