Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 120

Страница: 120 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 120 of 128

Fault

Cause

Corrective measures

cable, replace if necessary. Check
the installation position at various
points in the system.

Collision with system components

Check the system's layout, fasten
the affected components in such a
way that they cannot be collided
with, replace damaged compo-
nents.

Abrasive dust has collected at one of the more frequently
used transfer points (where the direction of travel is re-
versed).

Adjust the consumer's movement
profile. Move over the end position
to push the collected abrasive dust
out of the conductor bar. Clean the
conductor bar.

Insulating profile is not en-
gaged in the hanger clamp.

Conductor rail has not been properly mounted.

Clip in the insulation profile, check
components, replace if necessary

Use of damaged components.

Replace damaged components.

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды