Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 118

Страница: 118 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 118 of 128

CAUTION!

Before working on these components!

→

Disconnect the conductor rail system from the power supply

according to the 5 Safety Rules

and

secure it against being switched back on

For the 5 Safety Rules, see Section 2.5.

CAUTION!

Before switching the system on!

→

Each time before the product or system is started, measure the insulation resistance according to

locally applicable technical standards, directives and legal regulations.

→

Carry out locally required electrical tests.

CAUTION!

Alert personnel to the hazard!

→

Attach a sign stating “Risk of Death due to Electrical Shock” with the relevant hazard symbol in all

areas with access to components under voltage.

WARNING!

Fire hazard due to overload or sparking!

Fire hazards occur due to overloaded cables, electrical arcs, short circuits or sparking.

→

Before recommissioning, ensure that all work has been completed and all components have been

properly installed.

→

Conduct electrical testing as specified.

→

Permissible current values must be observed.

→

Electrical fuses must be installed in accordance with regulations.

→

Warn against misuse.

→

Do not store easily ignited materials near to conductor rails.

→

Dimensioning according to permissible system load capacity and provide for appropriate electrical

protective devices.

WARNING!

Risk of injury due to hot components!

Components can get hot during operation.

→

Operation is only permitted in areas inaccessible to the public and out of manual reach.

→

The danger zone must be enclosed by the customer or protection ensured by distance.

→

Cordon off the work area.

→

Use caution when working in the vicinity of the danger zone, particularly if protective devices (co-

vers, enclosures, control devices) have been removed or disabled.

→

Wear personal protective equipment!

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды