manualshive.com logo in svg

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Поделиться
Скачать
Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 6

Operating Instructions 

 

Single-pole Conductor Rail System 

SingleFlexLine Program 0815 

 

 

BAL0815-0002g-US 
www.conductix.us 

translated document 

page 6 of 128 

1.3

 

Copyright 

This document is subject to copyright and is exclusively intended for internal use by customers. 
Provision of the operating instructions to third parties, reproductions in any form – even in part – as well as the reuse and/or disclosure 
of their content are not permitted without the written approval of the manufacturer, except for the customer's internal use. 
 
Breach or infringement will result in liability for damages. This shall not affect our right to assert claims for further loss or damage. 

1.4

 

Replacement parts 

 

WARNING! 

Incorrect replacement parts are a safety hazard! 

Incorrect or faulty replacement parts can impair safety and result in damage, malfunctions or 

complete failure. 

→

 

Always use original replacement parts from the manufacturer! 

 
Order replacement parts from your contracted dealer or directly from the manufacturer. 
Contact details: See the last page of this document. 
Replacement parts list: see Section 12.1 Applicable documents.  

1.5

 

Material defects 

The terms governing material defects can be found in the General Terms and Conditions of Business. 

1.6

 

Technical support 

For technical support please contact our staff from the Customer Support Department. 
Contact details: See the last page of this document. 
 
We are also always interested in new information, experiences and feedback from the field that can help us improve our products. 
 

Содержание SingleFlexLine Program 0815

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды