manualshive.com logo in svg

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Поделиться
Скачать
Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 5

Operating Instructions 

 

Single-pole Conductor Rail System 

SingleFlexLine Program 0815 

 

 

BAL0815-0002g-US 
www.conductix.us 

translated document 

page 5 of 128 

1

 

General Information 

1.1

 

About this document 

The information provided in this manual is designed to enable the conductor rail system to be used safely and efficiently. 
 
This document is a component of the Conductor Rail System 0815 and must be kept accessible to personnel and in close proximity 
to the Conductor Rail System 0815 at all times. Personnel must read this document carefully and understand it before starting any 
work. Compliance with all safety and handling instructions provided in this document is a basic requirement for safe working. 
 
Local accident protection regulations and general safety guidelines for the area of use of the conductor rail system also apply. 
 
The illustrations in this document are provided for basic understanding and may deviate from the actual implementation of the system. 
 
In addition to these operating instructions, the instructions located in the appendices for the individual assembled components also 
apply. 

1.2

 

Limitation of liability 

All data and information in these operating instructions have been compiled while taking the valid standards and regulations as well 
as the state of the art and our many years of experience and knowledge into consideration. 
 
The manufacturer accepts no liability for damage resulting from: 
 

 

Failure to comply with operating instructions 

 

Unintended  use 

 

Use by untrained personnel 

 

Unauthorized modifications 

 

Technical changes 

 

Use of unauthorized replacement parts and accessories 

 
The actual scope of delivery may differ from the explanations and descriptions provided here if the model in question is a special 
one, if additional equipment has been ordered or due to recent technical changes. 
 
The obligations agreed upon in the delivery agreement and our General Terms and Conditions of Business apply, as do the Delivery 
Conditions of the manufacturer and all legal regulations applicable at the time the contract was concluded. 
 
All products are subject to technical modifications within the context of improvement of function and further development. 

 

 

Содержание SingleFlexLine Program 0815

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды