Conductix-Wampfler SingleFlexLine Program 0815 Скачать руководство пользователя страница 14

Страница: 14 / 128

Operating Instructions

Single-pole Conductor Rail System

SingleFlexLine Program 0815

BAL0815-0002g-US
www.conductix.us

translated document

page 14 of 128

DANGER!

Fire hazard due to overload or sparking!

Fire hazards occur due to overloaded cables, electrical arcs, short circuits or sparking. Spark-

ing can occur with poorly serviced, contaminated conductor rails or if the installation does not

comply with the required tolerances.

→

Permissible current values must be observed.

→

Comply with tolerances during installation.

→

Design and dimension systems in accordance with the permissible system load capacity and

provide appropriate protection devices.

→

Do not store inflammable and/or easily ignited materials near to conductor rails.

→

Inspect, service and clean conductor rails regularly and in accordance with specifications.

See Sections 8 and 9.

2.8.2

Mechanical hazards and sources of danger

DANGER!

Risk of injury due to ensnarement or impact!

Ensnarement and/or impact with moving conductor rails (slip ring) or current collectors con-

nected to the machine and other components must be prevented.

→

Cordon off the work area.

→

Use caution when working in the vicinity of the danger zone, particularly if protective devices

(covers, enclosures, control devices) have been removed or disabled.

→

Use caution when working in the vicinity of the danger zone, particularly below the conduc-

tor rail.

→

Wear personal protective equipment!

WARNING!

Secure conductor rails against falling!

→

In application areas with personnel traffic and at an installation height of 3 m or more, con-

ductor rails must be secured against falling.

CAUTION!

Risk of puncture wounds and cuts!

The packaging material can contain sharp objects such as nails, struts, steel bands and wood

splinters that can cause injury to limbs.

→

Wear personal protective equipment!

→

Cordon off the work area!

→

Use caution when working in the vicinity, particularly below the conductor rail!

Содержание SingleFlexLine Program 0815

































































































































Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды

Conductix-Wampfler SingleFlexLine Program 0815, Руководство по эксплуатации

Результаты поиска

Содержание SingleFlexLine Program 0815

Отзывы:

Бренды по названию

Популярные бренды