Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 7 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Chapter 12: Building the Stack with AT-StackQS Cards

........................................................................................... 159

Introduction........................................................................................................................................................................160

Powering On the Switches Sequentially............................................................................................................................161

Powering On the Switches Simultaneously .......................................................................................................................163

Chapter 13: Building the Stack with Copper or SFP Gigabit Ports

........................................................................... 165

Introduction........................................................................................................................................................................166

Command Summary..........................................................................................................................................................167

STACK ENABLE Command.......................................................................................................................................167

STACKPORT Command............................................................................................................................................167

STACK PRIORITY Command....................................................................................................................................167

STACK RENUMBER Command ................................................................................................................................169

SWITCH PROVISION Command...............................................................................................................................169

Configuring the Master Switch...........................................................................................................................................170

General Steps for the Master Switch..........................................................................................................................170

Configuring the Master Switch - Part I........................................................................................................................171

Configuring the Master Switch - Part II.......................................................................................................................173

Verifying the Master Switch........................................................................................................................................174

What to Do Next .........................................................................................................................................................176

Configuring the Member Switches.....................................................................................................................................177

General Steps for the Member Switches....................................................................................................................177

Configuring Member Switches - Part I........................................................................................................................178

Configuring Member Switches - Part II.......................................................................................................................179

Verifying Member Switches........................................................................................................................................181

What to Do Next for Member Switches ......................................................................................................................183

Powering on the Stack.......................................................................................................................................................184

Chapter 14: Cabling the Networking Ports

.................................................................................................................. 185

Cabling Copper Ports ........................................................................................................................................................186

Installing SFP and SFP+ Transceivers..............................................................................................................................188

Installing AT-SP10TW Direct Connect Cables ..................................................................................................................192

Cabling the AT-StackQS Card with AT-QSFPICU Cables ................................................................................................194

Cabling the AT-StackQS Card with Fiber Optic Transceivers ...........................................................................................196

Chapter 15: Troubleshooting

........................................................................................................................................ 197

Appendix A: Technical Specifications

......................................................................................................................... 203

Physical Specifications ......................................................................................................................................................204

Environmental Specifications.............................................................................................................................................206

Power Specifications .........................................................................................................................................................207

Certifications......................................................................................................................................................................209

RJ-45 Copper Port Pinouts................................................................................................................................................210

RJ-45 Style Serial Console Port Pinouts ...........................................................................................................................212

Stacking Transceivers .......................................................................................................................................................213

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды