Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 183 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

183

What to Do Next

for Member

Switches

After configuring the member switch, do the following:

1. Power off the member switch.

2. Repeat these procedures to configure all member switches, assigning

each one a unique ID number and identifying the Gigabit ports of the

trunk.

3. If you have not already configured the master switch, perform

“Configuring the Master Switch” on page 170.

4. Power off the master and all member switches.

5. Cable the Gigabit ports of the trunk on the master and member

switches. Refer to “Cabling Copper Ports” on page 186. For trunks of

SFP ports on AT-x930-28GSTX Switches, refer to “Installing SFP and

SFP+ Transceivers” on page 188. For cabling examples, refer to

“Trunks of Copper 10/100/1000Mbps Ports” on page 67 and “Trunks of

SFP Ports on AT-x930-28GSTX Switches” on page 69.

6. Perform “Powering on the Stack” on page 184.

7. Perform “Verifying the Stack and Assigning Priority Numbers” on

page 156 to confirm that the switches formed the stack.

8. Cable the networking ports, as explained in Chapter 14, “Cabling the

Networking Ports” on page 185.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды