Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 67 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Trunks of Copper 10/100/1000Mbps Ports

You can use the copper Gigabit ports on the front panels as the trunks for

stacks of x930 Switches. Here are the guidelines:



Stacks can have up to four switches.



Stacks can have both 28-port and 52-port x930 Switches.



Trunks can have up to eight copper Gigabit ports per switch.



For 52-port switches, use only ports in the range 1 to 24 for the

trunk ports.



You should try to use the same Gigabit ports as the trunk on all the

switches in the stack. This can make managing and

troubleshooting stacks easier.



You have to configure the master and member switches of the

stack by designating the Gigabit ports of the trunk with the STACK

ENABLE FRONT-PANEL-PORTS and STACKPORT commands,

and adding the members switches to the master switch as

provisioned switches.



The Gigabit ports of the trunk have to be at their default settings.

You cannot change the settings of trunk ports.

Note

Trunks of copper Gigabit ports require AlliedWare Plus version

5.5.1-2.1 or later.

For instructions, refer to Chapter 13, “Building the Stack with Copper or

SFP Gigabit Ports” on page 165

Here are examples of stacks with trunks of copper Gigabit ports. Figure 24

is of a stack of two switches. The trunk uses ports 1 to 4 on both switches.

(The maximum is eight ports per switch.) This is not a requirement, but

managing the stack will be easier if you select the same ports as the trunk

on all the switches and connect the same ports together, when possible.

Figure 24. Trunk of Copper Gigabit Ports for a Stack of Two Switches

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды