Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 180 / 214

Chapter 13: Building the Stack with Copper or SFP Gigabit Ports

180

Step 3 identifies the trunk type to be Gigabit ports.

Enter the STACK ENABLE FRONT-PANEL-PORTS command in the Global

Configuration mode to indicate that the trunk will be Gigabit ports. You have to

perform this command before designating the Gigabit ports:

awplus(config)# stack enable front-panel-ports

Steps 4 and 5 designate the Gigabit ports of the trunk on the member switch.

Enter the port Interface modes of the Gigabit ports that are to be the trunk on the

member switch. This example assumes the member switch has the ID 2 and the trunk

will have ports 1 to 8. Remember to change the switch ID number in the PORT

parameter as you configure each member switch:

awplus(config)# interface port2.0.1-2.0.8
awplus(config-if)#

Designate the ports as the stack trunk with the STACKPORT command.

awplus(config-if)# stackport
% Save the config and restart the system for this change to take
effect.

The remaining steps save your changes and reboot the switch.

Enter the EXIT command twice to return to the Privilege Exec mode.

awplus(config-if)# exit
awplus(config)# exit
awplus#

Save your changes with the WRITE command.

awplus# write
Building configuration ...
[OK]

Reboot the switch.

awplus# reboot
reboot system? (y/n):

Type “Y” for yes.

Wait one minute for the switch to start the AlliedWare Plus software.

Go to “Verifying Member Switches,” next.

Table 25. Configuring Member Switches - Part II (Continued)

Step

Description and Command

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды