Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 50 / 214

Chapter 1: Overview

The states of the LED when the switch is not operating in the low power

mode are shown in Figure 13.

Figure 13. Switch ID LED

The switch displays the letter “F” for fault on the ID LED if it detects one of

the following problems:



A cooling fan has failed.



The internal temperature of the switch has exceeded the normal

operating range and the switch may shut down.

Note

You can use the SHOW SYSTEM ENVIRONMENT command in the

command line interface to identify the source of the problem.

The states of the LED when the switch is operating in the low power mode

are shown in Figure 14.

Figure 14. Switch ID LEDs in the Low Power Mode

The switch is booting up.

The switch has encountered a fault condition.

The switch is operating as a stand-alone unit, with the ID
number 0.

The switch has an ID number of 1 to 8 as part of a VCStack.

The dot in the lower right corner flashes when the switch
accesses USB memory.

The switch is the master switch of a VCStack.

The switch is operating as a stand-alone unit.

The switch is a member switch of a VCStack.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды