Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 142 / 214

Chapter 10: Displaying the AlliedWare Plus Version Number

142

Starting a Local Management Session

The switch supports the following types of management:



Local management: Local management is performed through the

Console port on the management panel of the switch. The switch

does not require an IP address for local management.



Remote network: You can also manage the switch over your

network from your workstations. For this, the switch requires a

IPv4 or IPv6 address. The switch can obtain its address

automatically from a DCHP server on your network because it has

both DHCPv4 and DHCPv6 clients. The default setting for the

clients is enabled. If the switch does not receive a response to its

queries for an IP address, it uses the default IPv4 address

169.254.42.42/16.

This section explains how to start a local management session on the

Console port on the front panel of the switch with the management cable

included with the device. The management cable requires a computer or

terminal with a DB-9 (D-sub 9-pin) connector. Refer to Figure 70.

Figure 70. Management Cable Included with Switch

For computers without a DB-9 connector, such as laptop computers, Allied

Telesis offers the VT-Kit3 management cable. It has a male UB connector

that connects to a USB port on your workstation. Refer to Figure 71.

Figure 71. VT-Kit3 Management Cable

You connect the cable to the Console port on the switch with a standard,

straight-through Ethernet cable. Refer to Figure 72 on page 143. The VT-

Kit3 management cable and its software driver are sold separately.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды