Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 143 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

143

Figure 72. Management Workstation, VT-Kit3 Management Cable, and

Switch

This procedure explains how to start a local management session on the

switch with the management cable included with the device. For

instructions on how to start a remote management session, refer to the

x330 Series Software Reference for AlliedWare Plus Operating System

To start a local management session using the management cable

provided with the switch, perform the following procedure:

1. Power on one of the switches by doing one of the following:



If the switch has an AC power supply, connect the AC power cord

to the power supply on the back panel and to an AC power source.

if the switch has two power supplies, you need to power on only

one of them for this procedure.



If the switch has the DC AT-PWR250-80 Power Supply, power on

the DC circuit and the On/Off switch on the power supply. (If you

have not yet wired the DC connector on the power supply, refer to

Chapter 9, “Wiring the DC Connector on the AT-PWR250-80

Power Supply” on page 137.)

2. Wait one minute for the switch to initialize its management software.

3. Connect the RJ-45 connector on the management cable to the

Console port on the front panel of the switch. Refer to Figure 73 on

page 144.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды