Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 189 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

189

The illustrations in the procedure show the installation of a transceiver in

port 25 of a 28-port switch. The procedure is the same for all SFP and

SFP+ ports. The transceiver in the illustrations has a duplex LC connector.

Your transceivers may have different connectors.

To install transceivers, perform the following procedure:

1. If the transceiver port has a dust plug, remove it. Refer to Figure 84.

Figure 84. Removing the Dust Plug from an SFP+ Port

2. Remove the transceiver from its shipping container and store the

packaging material in a safe location.

3. If you are installing the transceiver in a top port, position the

transceiver with the Allied Telesis label facing up. If you are installing

the transceiver in a bottom port, position the transceiver with the label

facing down.

4. Slide the transceiver into the port until it clicks into place. Refer to

Figure 85.

Figure 85. Installing SFP+ Transceivers

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды