Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 46 / 214

Chapter 1: Overview

LEDs for the SFP

Ports

The LEDs for the twenty four SFP ports on the AT-x930-28GSTX Switch

are located between the ports. Refer to Figure 10. Each SFP port has one

LED. The left-hand LED is for the top port and the right-hand LED is for

the bottom port.

Figure 10. SFP Port LEDs

PoE

Green

The switch detects a powered device (PD)

on the port and is delivering power to it.

Solid Amber The switch has shut down PoE+ on the port

because of a fault condition.

Flashing

Amber

The switch detects a PD on the port but is

not delivering power to it because it has

reached its maximum power budget.

Off

This LED state can result from the following

conditions:



The port is not connected to a PD.



The PD is powered off.



The port is disabled in the

management software.



PoE is disabled on the port.



The LEDs on the Ethernet line cards

are turned off. To turn on the LEDs,

use the eco-friendly button.

Table 8. LEDs on the 10/100/1000Base-T Ports on the AT-x930-28GPX

and AT-x930-52GPX Switches (Continued)

LED

State

Description

SFP Port LEDs

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды