Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 42 / 214

Chapter 1: Overview

eco-friendly Button

The eco-friendly button on the front panel of the switch is used to toggle

the port LEDs on or off. You might turn off the LEDs to conserve electricity

when you are not monitoring the device. You can also toggle the LEDs

with the ECOFRIENDLY LED and NO ECOFRIENDLY LED commands in

the Global Configuration mode of the command line interface. The switch

is said to be operating in a low power mode when the LEDs are turned off.

Operating the switch in the low power mode with the LEDs turned off does

not interfere with the network operations of the device.

The management software on the switch has a command that blinks the

LEDs so that you can quickly and easily identify a specific unit among the

devices in an equipment rack. It is the FINDME command. The command

works on the switch even if you turned off the LEDs with the eco-friendly

button or NO ECOFRIENDLY LED command.

The Switch ID LED is always on, but it displays different information

depending on whether the LEDs are on or off. When the LEDs are on, the

ID LED displays the ID number of the switch. When the switch is operating

in the low power mode with the LEDs off, the ID LED indicates whether the

switch is a stand-alone unit or the master or member switch of a VCStack,

as detailed in Figure 14 on page 50.

Note

Before checking or troubleshooting the network connections to the

ports on the switch, you should always check to be sure that the

LEDs are on by either pressing the eco-friendly button or issuing the

ECOFRIENDLY LED and NO ECOFRIENDLY LED commands in

the Global Configuration mode of the command line interface.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды