Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 187 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

187



The default duplex mode setting of Auto-Negotiation is not

appropriate for ports connected to network devices that do not

support Auto-Negotiation and have a fixed duplex mode. You

should disable Auto-Negotiation on those ports and set their duplex

modes manually to avoid the possibility of duplex mode

mismatches. A switch port using Auto-Negotiation defaults to half-

duplex if it detects that the end node is not using Auto-Negotiation,

which can result in a mismatch if the end node is operating at a

fixed duplex mode of full-duplex.



Do not attach cables to ports of static or LACP port trunks until

after you have configured the trunks on the switch. Otherwise, the

ports will form network loops that can adversely affect network

performance.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды