Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 81 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Firmware Version

Number

Use this column to record the version numbers of

the AlliedWare Plus management software on

the switches. The switches might not be able to

form the stack if they have different versions.

Switches that have different versions should be

updated to the most recent release before you

build the stack. The configuration instructions

explain how to view the version numbers.

Trunk Ports

Use this column to enter the trunk ports. You

should choose the ports before beginning the

configuration procedures. Refer to “Stack Trunks”

on page 59.

Transceivers

Used this column to record the types of

transceivers in ports 25, 26, 27/S1, and 28/S2 of

28-port switches and ports 49, 50, 51/S1, and 52/

S2 of 52-port switches.

AT-x9EM/XT4 or

AT-StackQS Card

Use this column to enter the names of expansion

cards in the switches.

Table 18. Stacking Worksheet Columns (Continued)

Column

Description

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды