Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 85

Страница: 85 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Warning

Power cord is used as a disconnection device. To de-energize

equipment, disconnect the power cord.



Warning

Class I Equipment. This equipment must be earthed. The power

plug must be connected to a properly wired earth ground socket

outlet. An improperly wired socket outlet could place hazardous

voltages on accessible metal parts.



Note

Pluggable Equipment. The socket outlet shall be installed near the

equipment and shall be easily accessible.



Caution

Air vents must not be blocked and must have free access to the

room ambient air for cooling.



Warning

Operating Temperatures. All the switches are designed for a

maximum ambient temperature of 45° degrees C.



E52

Note

All Countries: Install product in accordance with local and National

Electrical Codes.



Warning

When installing this equipment, always ensure that the frame ground

connection is installed first and disconnected last.



E11

Warning

Only trained and qualified personnel are allowed to install or replace

this equipment.



E14

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды