Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 137 / 214

137

Chapter 9

Wiring the DC Connector on the AT-

PWR250-80 Power Supply

This chapter contains instructions on how to wire the DC connector on the

AT-PWR250-80 DC power supply.

Warning

As a safety precaution, install a circuit breaker with a minimum value

of 15 Amps between the equipment and the DC power source.



Warning

Always connect the wires to the LAN equipment first before

connecting them to the circuit breaker. Do not work with HOT feeds

to avoid the danger of physical injury from electrical shock. Always

verify that the circuit breaker is in the OFF position before connecting

the wires to the circuit breaker.



Warning

For centralized DC power connection, install only in a restricted

access area.



E23

Warning

This equipment must be installed in a Restricted Access location.



E45

Note

A tray cable is required to connect the power source if the unit is

listed Type TC tray cable and rated at 600 V and 90 degrees C, with

three conductors, minimum 14 AWG.



E24

To wire the DC connector on the AT-PWR250-80 DC Power Supply,

perform the following procedure:

1. Power off the DC circuit to which the switch will be connected.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды