Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 87

Страница: 87 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Note

If installed in a closed or multi-unit rack assembly, the operating

ambient temperature of the rack environment may be greater than

the room ambient temperature. Therefore, consideration should be

given to installing the equipment in an environment compatible with

the manufacturer’s maximum rated ambient temperature (Tmra).



E35

Caution

Installation of the equipment in a rack should be such that the

amount of air flow required for safe operation of the equipment is not

compromised.



E36

Warning

Reliable earthing of rack-mounted equipment should be maintained.

Particular attention should be given to supply connections other than

direct connections to the branch circuits (e.g., use of power strips).



E37

Warning

To reduce the risk of electric shock, the PoE ports on this product

must not connect to cabling that is routed outside the building where

this device is located.



E40

Warning

This product may have multiple AC power cords installed. To de-

energize this equipment, disconnect all power cords from the device.



E41

Caution

An Energy Hazard exists inside this equipment. Do not insert hands

or tools into open chassis slots or plugs.



E44

Warning

This equipment shall be installed in a Restricted Access location.



E45

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды