Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 40

Страница: 40 / 214

Chapter 1: Overview

S1 and S2 SFP+ Ports

SFP+ ports 27/S1 and 28/S2 on the front panels of the 28-port switches

and 51/S1 and 52/S2 on the 52-port switches can be used either as

regular Ethernet networking ports or as the trunk in a stack of up to eight

switches with the VCStack feature. The switches of a VCStack act as a

single virtual unit, synchronizing their actions so that switching operations,

like spanning tree protocols, virtual LANs, and static port trunks, span

across all of the units and ports. For more information, refer to Chapter 2,

“Virtual Chassis Stacking” on page 57.

Note

For a list of supported transceivers, refer to the product’s data sheet

on the Allied Telesis web site.

Note

The S1 and S2 ports are the default stack trunk ports if the switch

does not contain the AT-StackQS Card. To use the ports are regular

Ethernet networking ports, you must disable VCStack or use other

switch ports for the stack trunk. The ports on the AT-StackQS Card

are the default stack trunk ports if the card is installed.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды