Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 188 / 214

Chapter 14: Cabling the Networking Ports

188

Installing SFP and SFP+ Transceivers

This section contains instructions for installing SFP and SFP+ transceivers

in the ports on the switch.

Note

Refer to the product’s data sheet on the Allied Telesis web site for a

list of supported transceivers.

Here are the guidelines:



Ports 25 to 28 on 28-port x930 switches and ports 49 to 52 on 52-

port switches support 1000Mbps SFP and 10Gbps SFP+

transceivers. They do not support 100Mbps SFP transceivers.



Ports 1 to 24 on the AT-x930-28GSTX Switch support 100/

1000Mbps SFP transceivers. They do not support 10Gbps SFP+

transceivers.



If you are using SFP+ ports S1 and S2 as the VCStack trunk,

review the guidelines in “Trunks of Ports S1 and S2” on page 60

before performing this procedure.



SFP and SFP+ transceivers are hot-swappable. You may install

them while the switch is powered on.



The operational specifications and fiber optic cable requirements

of the transceivers are provided in the documents included with the

devices.



You should install a transceiver before connecting the fiber optic

cable.



Fiber optic transceivers are dust sensitive. Always keep the plug in

the optical bores when a fiber optic cable is not installed, or when

you store the transceiver. When you do remove the plug, keep it

for future use.



Unnecessary removal and insertion of a transceiver can lead to

premature failure.

Warning

Transceivers can be damaged by static electricity. Be sure to

observe all standard electrostatic discharge (ESD) precautions,

such as wearing an anti-static wrist strap, to avoid damaging the

devices.



E86

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды