Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 190

Страница: 190 / 214

Chapter 14: Cabling the Networking Ports

190

Note

If you are ready to attach the fiber optic cable to the transceiver,

continue with the next step. Otherwise, repeat steps 1 to 4 to install

the remaining transceivers in the switch.

5. Remove the dust cover from the transceiver. Refer to Figure 86.

Figure 86. Removing the Dust Cover from an SFP or SFP+ Transceiver

6. Verify the position of the handle on the transceiver. If the transceiver is

in a top port, the handle should be in the upright position, as shown in

Figure 87. If the transceiver is in a bottom port, the handle should be in

the down position.

Figure 87. Positioning the SFP or SFP+ Handle in the Upright Position

7. Connect the fiber optic cable to the transceiver, as shown in Figure 88

on page 191. The connector on the cable should fit snugly into the

port, and the tab should lock the connector into place.

SFP Handle

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды