Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 154

Страница: 154 / 214

Chapter 11: Building the Stack with SFP+ Ports S1 and S2

154

Powering On the Switches Simultaneously

This procedure powers on the switches simultaneously so that they assign

their ID numbers automatically by performing the following steps:

1. They start the AlliedWare Plus software.

2. They compare their switch priority numbers over the stack trunk.

3. Since they all have the same priority number, the default 128, they

compare MAC addresses.

4. The switch with the lowest MAC address becomes the master switch.

5. The master switch assigns itself the ID number 1.

6. The master switch assigns ID numbers in the range of 2 to 8 to the

other switches.

7. The other switches reboot the AlliedWare Plus software with their new

ID numbers.

This procedure assumes the following:



You performed “Displaying the Hardware Status and AlliedWare

Plus Version Number” on page 145 to confirm that all the switches

have the same version of the AlliedWare Plus software.



You performed “Designating SFP+ Ports S1 and S2 as the Stack

Trunk” on page 149 on any switches containing AT-StackQS

Cards.



This is the first power-on of the stack.



The switches are at their default settings.



The switches are powered off.

You can monitor the power-on sequence by connecting a terminal or PC

with a terminal emulator program to the Console port on any of the

switches. For the terminal settings, refer to “Starting a Local Management

Session” on page 142.

Note

Refer to “Power Specifications” on page 207 for the power

specifications of the switches.

After performing this procedure, go to “Verifying the Stack and Assigning

Priority Numbers” on page 156.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды