Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 149 / 214

x330 Series Installation Guide for Virtual Chassis Stacking

149

Designating SFP+ Ports S1 and S2 as the Stack Trunk

This procedure designates the SFP+ ports S1 and S2 ports as the trunk

ports on switches containing AT-StackQS Cards. Review the following

information before performing the command:



The SFP+ ports S1 and S2 are the default trunk ports in switches

that are at the default settings and do not contain AT-StackQS

Cards. If none of the switches for the stack contains the card, you

can skip this procedure and go to “Powering On the Switches

Sequentially” on page 152 or “Powering On the Switches

Simultaneously” on page 154.



For switches containing AT-StackQS Cards, the default trunk ports

are the two 40Gbps ports on the cards. To use the front panel

SFP+ ports S1 and S2 as the stack trunk instead, you have

perform the STACK ENABLE BUILTIN-PORTS command, as

explained in the following procedure. The command designates the

SFP+ ports S1 and S2 as the trunk ports and redefines the 40Gbps

ports on the cards as regular networking ports.



You must also perform this command if you designated front panel

Gigabit ports as the trunk, but later decide to use the SFP+ ports

S1 and S2 instead.



You should disconnect all cables from the SFP+ ports S1 and S2

and AT-StackQS Cards before performing the procedure.

This procedure assumes the following:



You performed the procedures in Chapter 10, “Displaying the

AlliedWare Plus Version Number” on page 141.



There are no cables connected to the SFP+ ports S1 and S2.



For switches with DC AT-PWR250-80 Power Supplies, you have

already wired the DC connectors. For instructions, refer to Chapter

9, “Wiring the DC Connector on the AT-PWR250-80 Power Supply”

on page 137

After performing this procedure on all switches containing AT-StackQS

Cards, do the following:

1. Power off all the switches that will be in the stack.

2. Cable the SFP+ ports S1 and S2 for the trunk. Refer to “Installing SFP

and SFP+ Transceivers” on page 188 and “Installing AT-SP10TW

Direct Connect Cables” on page 192.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды