Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 23 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

SFP Ports

The AT-x930-28GSTX Switch supports the following types of transceivers

in its twenty four SFP ports:



100Base-FX, 1000Base-T, and 1000Base-SX/LX SFP transceivers



Single-port BiDi 100Base-FX and 1000Base-LX SFP transceivers



1000Base-ZX SFP transceivers

Note

The SFP ports and copper ports on the AT-x930-28GSTX Switch

are paired together. Only one port in a pair can be active at a time.

For more information, refer to “SFP Ports” on page 38.

Note

SFP transceivers must be purchased separately. For a list of

supported transceivers, refer to the product's data sheet on the

Allied Telesis website.

SFP+ Ports

The four SFP+ ports support the following types of transceivers:



SFP 1000Base-SX/LX SFP transceivers



SFP single-port BiDi 1000Base-LX transceivers



SFP 1000Base-ZX transceivers



SFP+ 10Gbps, 10GBase-SR/LR fiber optic transceivers



SFP+ 10Gbps AT-SP10TW direct connect twinax cables with

SFP+ transceiver-style connectors

Note

The SFP+ ports do not support 100Mbps 100Base-FX transceivers.

Note

The port support full-duplex mode only. They do not support half-

duplex mode.

Note

SFP and SFP+ transceivers must be purchased separately. For a

list of supported transceivers, refer to the product’s data sheet on

the Allied Telesis web site.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды