Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 176

Страница: 176 / 214

Chapter 13: Building the Stack with Copper or SFP Gigabit Ports

176

What to Do Next

After configuring the master switch, do the following:

1. Power off the switch. For AC power supplies, disconnect the AC power

cords from the AC power sources. For DC power supplies, turn off the

ON/OFF switch on the power supplies or power off the DC power

circuits.

2. Configure the member switches. Refer to “Configuring the Member

Switches” on page 177.

3. After configuring the master switch and all member switches, build the

stack by cabling the trunk Gigabit ports on the switches. Refer to

“Cabling Copper Ports” on page 186 or “Installing SFP and SFP+

Transceivers” on page 188.

4. Power on the master and member switches of the stack. Refer to

“Powering on the Stack” on page 184.

5. Verify that the switches formed the stack by performing “Verifying the

Stack and Assigning Priority Numbers” on page 156.

6. Cable the networking ports. Refer to Chapter 14, “Cabling the

Networking Ports” on page 185.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды