Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 177 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

177

Configuring the Member Switches

This section contains the procedures for configuring the member switches

of the stack by assigning them ID numbers and designating Gigabit ports

as the stack trunk: Here are the procedures:



“General Steps for the Member Switches” on page 177



“Configuring Member Switches - Part I” on page 178



“Configuring Member Switches - Part II” on page 179



“Verifying Member Switches” on page 181



“What to Do Next for Member Switches” on page 183

You have to perform the procedures on each member switch individually,

before connecting the trunk Gigabit ports. The procedures should be

performed in the order presented here.

Note

The procedures require resetting member switches. Some network

traffic will be lost if the ports are connected to an active network.

General Steps for

the Member

Switches

Configuring the member switches has two parts. Part I has these main

steps:

1. Start a local management session on the switch.

2. Assign an ID number in the range of 2 to 4 to the member switch with

the SWITCH RENUMBER command in the Global Configuration

mode.

3. Save your changes with the WRITE command in the Privilege Exec

mode.

4. Restart the switch with the REBOOT command.

Part II has these main steps:

1. Start a new local management session with the switch.

2. Designate Gigabit front panel ports to be the trunk ports with the

STACK ENABLE FRONT-PANEL-PORTS command in the Global

Configuration mode. You have to perform this command before

designating the actual Gigabit ports of the trunk.

3. Designate up to eight Gigabit ports to be the stack trunk with the

STACKPORT command in the port interface modes.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды