Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 84 / 214

Chapter 3: Beginning the Installation

Reviewing Safety Precautions

Please review the following safety precautions before beginning the

installation procedure.

Note

Safety statements that have the



symbol are translated into

multiple languages in the

Translated Safety Statements

document at

www.alliedtelesis.com/support

Warning

Class 1 Laser product.



Warning

Laser Radiation.

Class 1M Laser product.

Warning

Do not stare into the laser beam.



Warning

Do not look directly at the fiber optic ends or inspect the cable ends

with an optical lens.



Warning

To prevent electric shock, do not remove the cover. No user-

serviceable parts inside. This unit contains hazardous voltages and

should only be opened by a trained and qualified technician. To

avoid the possibility of electric shock, disconnect electric power to

the product before connecting or disconnecting the LAN cables.



Warning

Do not work on equipment or cables during periods of lightning

activity.



Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды