Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 94 / 214

Chapter 4: Installing the Power Supplies

Installing the Power Supplies

This section contains the procedure for installing the power supplies in the

switch. If you are planning to install the switch in an equipment rack or on

a wall, it may be easier to install the power supplies first.

Caution

The device can be damaged by electrostatic discharge (ESD). Be

sure to follow standard ESD protections procedures, such as

wearing a wrist or foot strap, when installing the device.



E106

Caution

The switch is heavy. Always ask for assistance when moving or

lifting the device so as to avoid injuring yourself or damaging the

equipment.

The illustrations in the following procedure show the AT-PWR800 Power

Supply. The procedure is the same for all power supplies.

To install the power supplies, perform the following procedure:

1. Place the switch on a level, secure table or desk.

Note

If you are installing only one power supply, skip step 2.

2. Use a cross-head screwdriver to loosen the two captive screws on the

blank panel covering power supply slot B on the back panel and

remove it from the switch. Refer to Figure 33 on page 95.

Note

Allied Telesis recommends removing the blank panel from slot B

even if you are installing only one power supply, You reinstall the

panel later in the procedure.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды