Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 186 / 214

Chapter 14: Cabling the Networking Ports

186

Cabling Copper Ports

Here are the guidelines to cabling the 10/100/1000Base-T copper ports:



The cable specifications for the ports are listed in “Cable

Requirements” on page 32.



The connectors on the cables should fit snugly into the ports, and

the tabs should lock the connectors into place.



The default setting for the wiring configurations is auto-MDI/MDI-X.

The default setting is appropriate for switch ports that are

connected to 10/100Base-TX network devices that also support

auto-MDI/MDI-X.



The default auto-MDI/MDI-X setting is not appropriate for switch

ports that are connected to 10/100Base-TX network devices that

do not support auto-MDI/MDI-X and have a fixed wiring

configuration. For switch ports connected to those types of network

devices, you should disable auto-MDI/MDI-X and set the wiring

configurations manually.



The appropriate MDI/MDI-X setting for a switch port connected to a

10/100Base-TX network device with a fixed wiring configuration

depends on the setting of the network device and whether the

switch and network device are connected with straight-through or

crossover cable. If you are using straight-through copper cable, the

wiring configurations of a port on the switch and a port on a

network device must be opposite each other, such that one port

uses MDI and the other MDI-X. For example, if a network device

has a fixed wiring configuration of MDI, you must disable auto-MDI/

MDI-X on the corresponding switch port and manually set it to

MDI-X. If you are using crossover copper cable, the wiring

configurations of a port on the switch and a port on a network

device must be the same.



The default speed setting for the ports is Auto-Negotiation. This

setting is appropriate for ports connected to network devices that

also support Aut-Negotiation.



The default speed setting of Auto-Negotiation is not appropriate for

ports connected to 10/100Base-TX network devices that do not

support Auto-Negotiation and have fixed speeds. For those switch

ports, you should disable Auto-Negotiation and set the port’s

speed manually to match the speeds of the network devices.



The 10/100/1000Base-T ports must be set to Auto-Negotiation, the

default setting, to operate at 1000Mbps.



The default duplex mode setting for the ports is Auto-Negotiation.

This setting is appropriate for ports connected to network devices

that also support Auto-Negotiation for duplex modes.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды