Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 162 / 214

Chapter 12: Building the Stack with AT-StackQS Cards

162

To control the assignment of the switch ID numbers, perform the following

procedure:

1. Power on the x930 Switch you want assigned ID number 1:



If the switch has AC power supplies, connect the AC power cords

to the power supplies on the back panel and to AC power sources.



If the switch has DC AT-PWR250-80 Power Supplies, power on

the DC circuits and the On/Off switches on the power supply. (For

wiring instructions, refer to Chapter 9, “Wiring the DC Connector

on the AT-PWR250-80 Power Supply” on page 137.)

Warning

Power cord is used as a disconnection device. To de-energize

equipment, disconnect the power cord.



2. Wait one minute for the switch to start the AlliedWare Plus software.

The switch displays the number 1 on its ID LED and is now the master

switch.

3. Power on the x930 Switch you want assigned ID number 2.

4. Wait two minutes for the new switch to join the stack as a member.

The new switch automatically boots up twice before joining the stack

as a new member, once with the default ID number 1 and again with

the next available number, which is 2.

5. If there is a third switch, power it on and wait two minutes for it to join

the stack as a member with the ID number 3.

6. Repeat step 5 until all the switches are powered on.

The stack is now operational. The switches retain their ID numbers

even when reset or powered off.

7. To continue with the installation, go to “Verifying the Stack and

Assigning Priority Numbers” on page 156.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды