Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 31 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

10/100/1000Base-T Copper Ports

The copper ports on the switches are described in this section.

Speed

The ports can operate at 10, 100, or 1000 Mbps. The speeds may be set

manually using the management software or automatically with Auto-

Negotiation (IEEE 802.3u), the default setting.

Note

The ports must be set to Auto-Negotiation to function at 1000 Mbps

and are not compatible with devices that are not IEEE 802.3u

compliant.

Duplex Mode

The copper ports can operate in either half- or full-duplex mode. The

duplex mode of a port, like port speed, may be set manually using the

management software or automatically with Auto-Negotiation (IEEE

802.3u), the default setting.

The speed and duplex mode settings of a port may be set independently

of each other. For example, a port may be configured such that its speed

is set manually while its duplex mode is established through Auto-

Negotiation.

Note

A switch port should not use Auto-Negotiation to set its duplex mode

if it is connected to a network device that does not support Auto-

Negotiation for 10 or 100 Mbps operation and has a fixed duplex

mode of full-duplex. Otherwise, a duplex-mode mismatch may occur

in which a switch port and a network device operate at different

duplex modes. The duplex modes of switch ports that are connected

to network devices that do not support Auto-Negotiation should be

set manually through the management software.

Wiring

Configuration

The wiring configuration of a port operating at 10 or 100 Mbps can be MDI

or MDI-X. The wiring configurations of a switch port and a network device

connected with straight-through copper cabling have to be opposite, such

that one device is using MDI and the other MDI-X. For instance, a switch

port has to be set to MDI-X if it is connected to a network device set to

MDI.

You may set the wiring configurations of the ports manually or let the

switch configure them automatically with auto-MDI/MDI-X (IEEE 802.3ab-

compliant). This feature enables the switch to automatically negotiate with

network devices to establish their proper settings.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды