Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 144

Страница: 144 / 214

Chapter 10: Displaying the AlliedWare Plus Version Number

144

Figure 73. Connecting the Management Cable to the Console Port

4. Connect the other end of the cable to an RS-232 port on a terminal or

PC with a terminal emulator program.

5. Configure the terminal or terminal emulator program as follows:



Baud rate: 9600 bps (The baud rate of the Console Port is

adjustable from 1200 to 115200 bps. The default is 9600 bps.)



Data bits: 8



Parity: None



Stop bits: 1



Flow control: None

Note

The port settings are for a DEC VT100 or ANSI terminal, or an

equivalent terminal emulator program.

6. Press Enter.

You are prompted for a user name and password.

7. If this is the initial management session of the switch, enter “manager”

as the user name and “friend” as the password. The user name and

password are case sensitive.

The local management session starts when the User Exec mode

prompt, shown in Figure 74. is displayed.

Figure 74. User Exec Mode Prompt

The User Exec mode is the first level in the command mode interface.

For complete information on the modes and commands, refer to the

Software Reference for x930 Series Switches, AlliedWare Plus

Operating System

awplus>

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды