Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 196 / 214

Chapter 14: Cabling the Networking Ports

196

Cabling the AT-StackQS Card with Fiber Optic Transceivers

This section contains the procedure for cabling AT-StackQS Cards with

AT-QSFPSR and AT-QSFPLR4 Transceivers. For instructions on

installing the cards in switches, refer to Chapter 5, “Installing AT-StackQS

and AT-x9EM/XT4 Cards” on page 103

If you are using the ports on the card for the VCStack trunk, review the

guidelines in “Trunks of AT-StackQS Cards” on page 64 before performing

this procedure.

For the maximum operating distances and cable requirements of the

transceivers, refer to the

x930 Data Sheet

on the Allied Telesis website for

the list of supported transceivers for the AT-StackQS card.

The transceivers are hot-swappable. You can install them while the

switches are powered on.

To cable the AT-StackQS Cards with fiber optic transceivers, perform the

following procedure:

1. Remove the dust cover from one of the ports on the AT-StackQS

Card.

2. Slide a transceivers into the port until it clicks into place.

3. Attach a fiber optic cable to the transceiver.

4. Repeat this procedure to install and cable a transceiver in the second

port.

5. If you are using the cards for the VCStack trunk, install and cable

cards in the other switches of the stack. The connections must

crossover on the switches. Port 1 on the card in one switch must be

connected to port 2 in the next switch.

6. If you are using the cards for the VCStack trunk, go to Chapter 12,

“Building the Stack with AT-StackQS Cards” on page 159 after cabling

all the switches.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды