Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 197 / 214

197

Chapter 15

Troubleshooting

This chapter contains suggestions on how to troubleshoot the switch if a

problem occurs.

Note

For further assistance, please contact Allied Telesis Technical

Support at

www.alliedtelesis.com/support

Problem 1:

All of the port LEDs and the Switch ID LED are off, and the

fans are not operating.

Solutions:

The unit is not receiving power. If the switch has an AC power

supply, try the following:



Verify that the power cord is securely connected to the power

source and to the AC connector on the back panel of the switch.



Verify that the power outlet has power by connecting another

device to it.



Try connecting the unit to another power source.



Try a different power cord.



Verify that the voltage from the power source is within the required

levels for your region.

If the switch has the DC AT-PWR250-80 Power Supply, try the following:



Verify that the DC circuit is powered on.



Verify that the On/Off switch on the power supply is in the On

position.



Verify that the positive, negative, and ground wires are properly

connected to the AT-PWR250-80 Power Supply and DC circuit.

Refer to “Wiring the DC Connector on the AT-PWR250-80 Power

Supply” on page 137.



Try connecting the switch to another DC circuit.



Try replacing the positive, negative, and ground wires.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды