Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 171 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

171

5. Save your changes with the WRITE command in the Privilege Exec

mode.

Here are the main steps to Part II:

1. Add the member switches as provisioned units to the configuration of

the master switch, with the SWITCH PROVISION command.

2. Designate up to eight Gigabit ports on the provisioned member

switches to be the stack trunk with the STACKPORT command in the

port interface modes.

3. Save your changes to the master switch with the WRITE command in

the Privilege Exec mode.

4. Reboot the master switch with the REBOOT command.

5. Start a new local management session.

6. Verify the changes on the master switch with the SHOW STACK and

SHOW RUNNING-CONFIG INTERFACE command.

Configuring the

Master Switch -

Part I

To configure Gigabit ports on the master switch as the stack trunk, start by

performing the procedure in Table 22.

Table 22. Configuring the Master Switch to Use Gigabit Ports as the Stack Trunk - Part I

Step

Description and Command

Power on the switch to be the master switch and start a local management session.

Any x930 Switch can be the master switch of a stack. Refer to “Starting a Local

Management Session” on page 142.

Enter the ENABLE and CONFIGURE TERMINAL commands to move to the Global

Configuration mode.

awplus> enable
awplus# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
awplus(config)#

Step 3 designates Gigabit ports as the stack trunk with the STACK ENABLE FRONT-PANEL-

PORTS command.

Enter the STACK ENABLE FRONT-PANEL-PORTS command in the Global

Configuration mode to designate Gigabit ports as the stack trunk. You have to

perform this command before designating the actual trunk ports:

awplus(config)# stack enable front-panel-ports

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды