Skoda Rapid NH 2014 Workshop Manual Download

Page: 52 / 319

Removing and installing fuel tank lid unit (Spacebook)

Removing
– Unlock the catches - arrows -, which are clipped onto the side

panel- 2 -, in the same way as in the Rapid model

⇒ “3.2 Removing and installing fuel tank lid unit”, page 42

– Remove fuel tank lid unit - 1 - outwards.
Installing
– Perform the installation by pressing in the fuel tank lid unit in

the lateral part. Latch the fuel tank lid unit for the correct po‐

sition until it audibly clicks into place.

Note

If the latches for the fuel tank lid unit are damaged, use a new part.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

Rep. gr.55 - Bonnet, rear lid

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands