Skoda Rapid NH 2014 Workshop Manual Download

Page: 190 / 319

– Install screws -3- (2.5 Nm) and -1- (1.5 Nm).

3.3.2

Removing and installing door sill panels

Note

♦

The ambient temperature as well as the temperature of the

parts must be at least 18 °C, maximum 30 °C.

♦

After glueing the tuning parts, the vehicle must remain in a

warm room for at least 24 hours.

♦

Before glueing, all of the adhesive surfaces must be de‐

greased with good quality - the quality of the glued joint de‐

pends upon this!

♦

Ensure thorough ventilation of the working area.

♦

The adhesive surface of attachments must not be painted!

♦

Attachments can only be glued to the vehicle after thorough

curing of the body paint.

Adhesive mate‐

rials

Part number

Purpose, application range

Denomination, manufacturer,

comment

Glue sealing

material

Betalink K2

Glue tuning parts to the body.

Observe the manufacturer

DOW’s instructions.

Activator

Betaprime 5600-1 Prepare the surfaces before gluing to

improve adhesion.

DOW

Cleaning solu‐

tion

Terostat 8550

For cleaning all surfaces to which

glass/paint primer and glue is applied.

Henkel

Applicator

D 009 500 25

For applying the activator.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

182

Rep. gr.66 - Exterior equipment

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands