manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

The Skoda Rapid NH 2014 Workshop Manual is a comprehensive guide designed to assist users in the maintenance, repair, and troubleshooting of their vehicle. This manual provides detailed instructions and diagrams, allowing for efficient and reliable DIY car maintenance. Download this invaluable resource for free from manualshive.com.

Share
Download
background image

Installing
– The installation occurs in reverse order.

Note

Adjust the tailgate after installing 

⇒ “2.4 Adjusting tailgate”, page 37

 .

2.3

Removing and installing the locking

mechanism

2.3.1

Removing

– Unscrew screw -2- and remove the closing wedge -1- from the

luggage compartment wall.

Installing
– The installation occurs in reverse order.
– Set the locking mechanism

⇒ “2.4.1 Setting the locking mechanism”, page 39

 .

2.4

Adjusting tailgate

Note

♦

The vehicle must be standing on its wheels in order to adjust the tailgate.

♦

The flap lock is directly screwed onto the tailgate. It has no elongated holes and therefore it cannot be

adjusted.

♦

The adjusting buffers on the left and right are not used for the adjustment. They have the function to stabilise

or dampen the bonnet.

♦

The bonnet is correctly adjusted if in the closed state it has an overall even gap size, is not positioned too

far outwards or inwards and the contours are aligned.

♦

The tailgate must latch in the flap lock without using increased force.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Tailgate    

37

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Related manuals for Rapid NH 2014

Saab 99 Important Operatlng, Safety And Maintenance Instructions preview
99
Brand: Saab Pages: 75
N-Com B3 User Instructions And Safety preview
B3
Brand: N-Com Pages: 28
Harken Hoister SUP Manual preview
SUP
Brand: Harken Hoister Pages: 12
Yamaha Raptor Instruction Supplement preview
Raptor
Brand: Yamaha Pages: 2
Jabra FREEWAY Datasheet preview
FREEWAY
Brand: Jabra Pages: 2
Jabra BT330 User Manual preview
BT330
Brand: Jabra Pages: 38
IAG IAG-ENG-5003BK Instructions preview
IAG-ENG-5003BK
Brand: IAG Pages: 3
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Brand: BrandMotion Pages: 8
Yakima Whispbar K887W Fitting Instructions Manual preview
Whispbar K887W
Brand: Yakima Pages: 19
Nav TV UCI-11C NTV-KIT331 User Manual preview
UCI-11C NTV-KIT331
Brand: Nav TV Pages: 4
Bestop WrapAround Windjammer Installation Instructions Manual preview
WrapAround Windjammer
Brand: Bestop Pages: 7
GMC TopKick 2007 Owner'S Manual preview
TopKick 2007
Brand: GMC Pages: 430
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Brand: Ecco Pages: 24
Saab 9000 1985 Service Manual preview
9000 1985
Brand: Saab Pages: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Brand: A-rival Pages: 23
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Brand: Carcomm Pages: 2
Edelbrock 8135 Installation Instructions preview
8135
Brand: Edelbrock Pages: 4
Volvo 1997 850 Service Manual preview
1997 850
Brand: Volvo Pages: 62

Brands by name

Popular brands

Load more brands