Skoda Rapid NH 2014 Workshop Manual Download

Page: 93 / 319

Central locking

Note

The control motors of the front and rear doors central locking are

component parts of the door locks and cannot be replaced indi‐

vidually.

– Removing and installing the door lock

⇒ “2.8 Removing and installing the door lock”, page 65

– After replacing the door lock with central locking motor, inter‐

rogate the event memory and erase ⇒ Vehicle diagnostic

tester Self-Diagnosis for Convenience System.

3.1

Adjustment of radio control keys

3.2

Summary of components – battery for the (foldable) radio control key

1 - Key with transponder alter‐

nating code
2 - Radio container - top part
3 - LED

❑ This LED must flash

when operating the ra‐

dio remote control.

❑ If the LED does not flash

when operating the ra‐

dio remote control, the

battery is discharged

and must be changed.

4 - Battery

❑ Removing and installing

⇒ “3.3 Removing and in‐

stalling the battery for

the foldable key with ra‐

dio remote control ”,

page 86

5 - Radio container - bottom

part

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

3. Central locking

Volkswagen Technical Site: http://vwts.ru http://vwts.info

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands