Skoda Rapid NH 2014 Workshop Manual Download

Page: 246 / 319

Installing

WARNING

♦ Observe the general safety instructions for working on air‐

bag, belt tensioner and battery separation units (pyrotech‐

nical components)

⇒ page 225

♦ Prior to the handling of pyrotechnical components (for ex‐

ample, disconnecting the electrical plug connection) the

person who carries out this operation must “discharge

himself electrostatically”. For this purpose, briefly touch

the door lock, for example.

– The installation occurs in reverse order.

Note

♦

Make sure the plug connection is pushed in as far as it can go

and audibly clicks into place.

♦

Make sure that the electric cables are not trapped.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

238

Rep. gr.69 - Passenger protection

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands